| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mpls: add seqcount to protect the platform_label{,s} pair
The RCU-protected codepaths (mpls_forward, mpls_dump_routes) can have
an inconsistent view of platform_labels vs platform_label in case of a
concurrent resize (resize_platform_label_table, under
platform_mutex). This can lead to OOB accesses.
This patch adds a seqcount, so that we get a consistent snapshot.
Note that mpls_label_ok is also susceptible to this, so the check
against RTA_DST in rtm_to_route_config, done outside platform_mutex,
is not sufficient. This value gets passed to mpls_label_ok once more
in both mpls_route_add and mpls_route_del, so there is no issue, but
that additional check must not be removed. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915/dsi: Don't do DSC horizontal timing adjustments in command mode
Stop adjusting the horizontal timing values based on the
compression ratio in command mode. Bspec seems to be telling
us to do this only in video mode, and this is also how the
Windows driver does things.
This should also fix a div-by-zero on some machines because
the adjusted htotal ends up being so small that we end up with
line_time_us==0 when trying to determine the vtotal value in
command mode.
Note that this doesn't actually make the display on the
Huawei Matebook E work, but at least the kernel no longer
explodes when the driver loads.
(cherry picked from commit 0b475e91ecc2313207196c6d7fd5c53e1a878525) |
| In the Linux kernel, the following vulnerability has been resolved:
openvswitch: defer tunnel netdev_put to RCU release
ovs_netdev_tunnel_destroy() may run after NETDEV_UNREGISTER already
detached the device. Dropping the netdev reference in destroy can race
with concurrent readers that still observe vport->dev.
Do not release vport->dev in ovs_netdev_tunnel_destroy(). Instead, let
vport_netdev_free() drop the reference from the RCU callback, matching
the non-tunnel destroy path and avoiding additional synchronization
under RTNL. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus/core) Protect regulator operations with mutex
The regulator operations pmbus_regulator_get_voltage(),
pmbus_regulator_set_voltage(), and pmbus_regulator_list_voltage()
access PMBus registers and shared data but were not protected by
the update_lock mutex. This could lead to race conditions.
However, adding mutex protection directly to these functions causes
a deadlock because pmbus_regulator_notify() (which calls
regulator_notifier_call_chain()) is often called with the mutex
already held (e.g., from pmbus_fault_handler()). If a regulator
callback then calls one of the now-protected voltage functions,
it will attempt to acquire the same mutex.
Rework pmbus_regulator_notify() to utilize a worker function to
send notifications outside of the mutex protection. Events are
stored as atomics in a per-page bitmask and processed by the worker.
Initialize the worker and its associated data during regulator
registration, and ensure it is cancelled on device removal using
devm_add_action_or_reset().
While at it, remove the unnecessary include of linux/of.h. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: prevent immediate PASID reuse case
PASID resue could cause interrupt issue when process
immediately runs into hw state left by previous
process exited with the same PASID, it's possible that
page faults are still pending in the IH ring buffer when
the process exits and frees up its PASID. To prevent the
case, it uses idr cyclic allocator same as kernel pid's.
(cherry picked from commit 8f1de51f49be692de137c8525106e0fce2d1912d) |
| In the Linux kernel, the following vulnerability has been resolved:
net: bonding: fix use-after-free in bond_xmit_broadcast()
bond_xmit_broadcast() reuses the original skb for the last slave
(determined by bond_is_last_slave()) and clones it for others.
Concurrent slave enslave/release can mutate the slave list during
RCU-protected iteration, changing which slave is "last" mid-loop.
This causes the original skb to be double-consumed (double-freed).
Replace the racy bond_is_last_slave() check with a simple index
comparison (i + 1 == slaves_count) against the pre-snapshot slave
count taken via READ_ONCE() before the loop. This preserves the
zero-copy optimization for the last slave while making the "last"
determination stable against concurrent list mutations.
The UAF can trigger the following crash:
==================================================================
BUG: KASAN: slab-use-after-free in skb_clone
Read of size 8 at addr ffff888100ef8d40 by task exploit/147
CPU: 1 UID: 0 PID: 147 Comm: exploit Not tainted 7.0.0-rc3+ #4 PREEMPTLAZY
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:123)
print_report (mm/kasan/report.c:379 mm/kasan/report.c:482)
kasan_report (mm/kasan/report.c:597)
skb_clone (include/linux/skbuff.h:1724 include/linux/skbuff.h:1792 include/linux/skbuff.h:3396 net/core/skbuff.c:2108)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5334)
bond_start_xmit (drivers/net/bonding/bond_main.c:5567 drivers/net/bonding/bond_main.c:5593)
dev_hard_start_xmit (include/linux/netdevice.h:5325 include/linux/netdevice.h:5334 net/core/dev.c:3871 net/core/dev.c:3887)
__dev_queue_xmit (include/linux/netdevice.h:3601 net/core/dev.c:4838)
ip6_finish_output2 (include/net/neighbour.h:540 include/net/neighbour.h:554 net/ipv6/ip6_output.c:136)
ip6_finish_output (net/ipv6/ip6_output.c:208 net/ipv6/ip6_output.c:219)
ip6_output (net/ipv6/ip6_output.c:250)
ip6_send_skb (net/ipv6/ip6_output.c:1985)
udp_v6_send_skb (net/ipv6/udp.c:1442)
udpv6_sendmsg (net/ipv6/udp.c:1733)
__sys_sendto (net/socket.c:730 net/socket.c:742 net/socket.c:2206)
__x64_sys_sendto (net/socket.c:2209)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
</TASK>
Allocated by task 147:
Freed by task 147:
The buggy address belongs to the object at ffff888100ef8c80
which belongs to the cache skbuff_head_cache of size 224
The buggy address is located 192 bytes inside of
freed 224-byte region [ffff888100ef8c80, ffff888100ef8d60)
Memory state around the buggy address:
ffff888100ef8c00: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
ffff888100ef8c80: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff888100ef8d00: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
^
ffff888100ef8d80: fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb fb
ffff888100ef8e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
================================================================== |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: dwc: ep: Flush MSI-X write before unmapping its ATU entry
Endpoint drivers use dw_pcie_ep_raise_msix_irq() to raise an MSI-X
interrupt to the host using a writel(), which generates a PCI posted write
transaction. There's no completion for posted writes, so the writel() may
return before the PCI write completes. dw_pcie_ep_raise_msix_irq() also
unmaps the outbound ATU entry used for the PCI write, so the write races
with the unmap.
If the PCI write loses the race with the ATU unmap, the write may corrupt
host memory or cause IOMMU errors, e.g., these when running fio with a
larger queue depth against nvmet-pci-epf:
arm-smmu-v3 fc900000.iommu: 0x0000010000000010
arm-smmu-v3 fc900000.iommu: 0x0000020000000000
arm-smmu-v3 fc900000.iommu: 0x000000090000f040
arm-smmu-v3 fc900000.iommu: 0x0000000000000000
arm-smmu-v3 fc900000.iommu: event: F_TRANSLATION client: 0000:01:00.0 sid: 0x100 ssid: 0x0 iova: 0x90000f040 ipa: 0x0
arm-smmu-v3 fc900000.iommu: unpriv data write s1 "Input address caused fault" stag: 0x0
Flush the write by performing a readl() of the same address to ensure that
the write has reached the destination before the ATU entry is unmapped.
The same problem was solved for dw_pcie_ep_raise_msi_irq() in commit
8719c64e76bf ("PCI: dwc: ep: Cache MSI outbound iATU mapping"), but there
it was solved by dedicating an outbound iATU only for MSI. We can't do the
same for MSI-X because each vector can have a different msg_addr and the
msg_addr may be changed while the vector is masked.
[bhelgaas: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: unconditionally bump set->nelems before insertion
In case that the set is full, a new element gets published then removed
without waiting for the RCU grace period, while RCU reader can be
walking over it already.
To address this issue, add the element transaction even if set is full,
but toggle the set_full flag to report -ENFILE so the abort path safely
unwinds the set to its previous state.
As for element updates, decrement set->nelems to restore it.
A simpler fix is to call synchronize_rcu() in the error path.
However, with a large batch adding elements to already maxed-out set,
this could cause noticeable slowdown of such batches. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: tegra210-quad: Protect curr_xfer check in IRQ handler
Now that all other accesses to curr_xfer are done under the lock,
protect the curr_xfer NULL check in tegra_qspi_isr_thread() with the
spinlock. Without this protection, the following race can occur:
CPU0 (ISR thread) CPU1 (timeout path)
---------------- -------------------
if (!tqspi->curr_xfer)
// sees non-NULL
spin_lock()
tqspi->curr_xfer = NULL
spin_unlock()
handle_*_xfer()
spin_lock()
t = tqspi->curr_xfer // NULL!
... t->len ... // NULL dereference!
With this patch, all curr_xfer accesses are now properly synchronized.
Although all accesses to curr_xfer are done under the lock, in
tegra_qspi_isr_thread() it checks for NULL, releases the lock and
reacquires it later in handle_cpu_based_xfer()/handle_dma_based_xfer().
There is a potential for an update in between, which could cause a NULL
pointer dereference.
To handle this, add a NULL check inside the handlers after acquiring
the lock. This ensures that if the timeout path has already cleared
curr_xfer, the handler will safely return without dereferencing the
NULL pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix data-race warning and potential load/store tearing
Fix the following:
BUG: KCSAN: data-race in rxrpc_peer_keepalive_worker / rxrpc_send_data_packet
which is reporting an issue with the reads and writes to ->last_tx_at in:
conn->peer->last_tx_at = ktime_get_seconds();
and:
keepalive_at = peer->last_tx_at + RXRPC_KEEPALIVE_TIME;
The lockless accesses to these to values aren't actually a problem as the
read only needs an approximate time of last transmission for the purposes
of deciding whether or not the transmission of a keepalive packet is
warranted yet.
Also, as ->last_tx_at is a 64-bit value, tearing can occur on a 32-bit
arch.
Fix both of these by switching to an unsigned int for ->last_tx_at and only
storing the LSW of the time64_t. It can then be reconstructed at need
provided no more than 68 years has elapsed since the last transmission. |
| In the Linux kernel, the following vulnerability has been resolved:
dst: fix races in rt6_uncached_list_del() and rt_del_uncached_list()
syzbot was able to crash the kernel in rt6_uncached_list_flush_dev()
in an interesting way [1]
Crash happens in list_del_init()/INIT_LIST_HEAD() while writing
list->prev, while the prior write on list->next went well.
static inline void INIT_LIST_HEAD(struct list_head *list)
{
WRITE_ONCE(list->next, list); // This went well
WRITE_ONCE(list->prev, list); // Crash, @list has been freed.
}
Issue here is that rt6_uncached_list_del() did not attempt to lock
ul->lock, as list_empty(&rt->dst.rt_uncached) returned
true because the WRITE_ONCE(list->next, list) happened on the other CPU.
We might use list_del_init_careful() and list_empty_careful(),
or make sure rt6_uncached_list_del() always grabs the spinlock
whenever rt->dst.rt_uncached_list has been set.
A similar fix is neeed for IPv4.
[1]
BUG: KASAN: slab-use-after-free in INIT_LIST_HEAD include/linux/list.h:46 [inline]
BUG: KASAN: slab-use-after-free in list_del_init include/linux/list.h:296 [inline]
BUG: KASAN: slab-use-after-free in rt6_uncached_list_flush_dev net/ipv6/route.c:191 [inline]
BUG: KASAN: slab-use-after-free in rt6_disable_ip+0x633/0x730 net/ipv6/route.c:5020
Write of size 8 at addr ffff8880294cfa78 by task kworker/u8:14/3450
CPU: 0 UID: 0 PID: 3450 Comm: kworker/u8:14 Tainted: G L syzkaller #0 PREEMPT_{RT,(full)}
Tainted: [L]=SOFTLOCKUP
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025
Workqueue: netns cleanup_net
Call Trace:
<TASK>
dump_stack_lvl+0xe8/0x150 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xca/0x240 mm/kasan/report.c:482
kasan_report+0x118/0x150 mm/kasan/report.c:595
INIT_LIST_HEAD include/linux/list.h:46 [inline]
list_del_init include/linux/list.h:296 [inline]
rt6_uncached_list_flush_dev net/ipv6/route.c:191 [inline]
rt6_disable_ip+0x633/0x730 net/ipv6/route.c:5020
addrconf_ifdown+0x143/0x18a0 net/ipv6/addrconf.c:3853
addrconf_notify+0x1bc/0x1050 net/ipv6/addrconf.c:-1
notifier_call_chain+0x19d/0x3a0 kernel/notifier.c:85
call_netdevice_notifiers_extack net/core/dev.c:2268 [inline]
call_netdevice_notifiers net/core/dev.c:2282 [inline]
netif_close_many+0x29c/0x410 net/core/dev.c:1785
unregister_netdevice_many_notify+0xb50/0x2330 net/core/dev.c:12353
ops_exit_rtnl_list net/core/net_namespace.c:187 [inline]
ops_undo_list+0x3dc/0x990 net/core/net_namespace.c:248
cleanup_net+0x4de/0x7b0 net/core/net_namespace.c:696
process_one_work kernel/workqueue.c:3257 [inline]
process_scheduled_works+0xad1/0x1770 kernel/workqueue.c:3340
worker_thread+0x8a0/0xda0 kernel/workqueue.c:3421
kthread+0x711/0x8a0 kernel/kthread.c:463
ret_from_fork+0x510/0xa50 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246
</TASK>
Allocated by task 803:
kasan_save_stack mm/kasan/common.c:57 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:78
unpoison_slab_object mm/kasan/common.c:340 [inline]
__kasan_slab_alloc+0x6c/0x80 mm/kasan/common.c:366
kasan_slab_alloc include/linux/kasan.h:253 [inline]
slab_post_alloc_hook mm/slub.c:4953 [inline]
slab_alloc_node mm/slub.c:5263 [inline]
kmem_cache_alloc_noprof+0x18d/0x6c0 mm/slub.c:5270
dst_alloc+0x105/0x170 net/core/dst.c:89
ip6_dst_alloc net/ipv6/route.c:342 [inline]
icmp6_dst_alloc+0x75/0x460 net/ipv6/route.c:3333
mld_sendpack+0x683/0xe60 net/ipv6/mcast.c:1844
mld_send_cr net/ipv6/mcast.c:2154 [inline]
mld_ifc_work+0x83e/0xd60 net/ipv6/mcast.c:2693
process_one_work kernel/workqueue.c:3257 [inline]
process_scheduled_works+0xad1/0x1770 kernel/workqueue.c:3340
worker_thread+0x8a0/0xda0 kernel/workqueue.c:3421
kthread+0x711/0x8a0 kernel/kthread.c:463
ret_from_fork+0x510/0xa50 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entr
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: qrtr: Drop the MHI auto_queue feature for IPCR DL channels
MHI stack offers the 'auto_queue' feature, which allows the MHI stack to
auto queue the buffers for the RX path (DL channel). Though this feature
simplifies the client driver design, it introduces race between the client
drivers and the MHI stack. For instance, with auto_queue, the 'dl_callback'
for the DL channel may get called before the client driver is fully probed.
This means, by the time the dl_callback gets called, the client driver's
structures might not be initialized, leading to NULL ptr dereference.
Currently, the drivers have to workaround this issue by initializing the
internal structures before calling mhi_prepare_for_transfer_autoqueue().
But even so, there is a chance that the client driver's internal code path
may call the MHI queue APIs before mhi_prepare_for_transfer_autoqueue() is
called, leading to similar NULL ptr dereference. This issue has been
reported on the Qcom X1E80100 CRD machines affecting boot.
So to properly fix all these races, drop the MHI 'auto_queue' feature
altogether and let the client driver (QRTR) manage the RX buffers manually.
In the QRTR driver, queue the RX buffers based on the ring length during
probe and recycle the buffers in 'dl_callback' once they are consumed. This
also warrants removing the setting of 'auto_queue' flag from controller
drivers.
Currently, this 'auto_queue' feature is only enabled for IPCR DL channel.
So only the QRTR client driver requires the modification. |
| In the Linux kernel, the following vulnerability has been resolved:
functionfs: fix the open/removal races
ffs_epfile_open() can race with removal, ending up with file->private_data
pointing to freed object.
There is a total count of opened files on functionfs (both ep0 and
dynamic ones) and when it hits zero, dynamic files get removed.
Unfortunately, that removal can happen while another thread is
in ffs_epfile_open(), but has not incremented the count yet.
In that case open will succeed, leaving us with UAF on any subsequent
read() or write().
The root cause is that ffs->opened is misused; atomic_dec_and_test() vs.
atomic_add_return() is not a good idea, when object remains visible all
along.
To untangle that
* serialize openers on ffs->mutex (both for ep0 and for dynamic files)
* have dynamic ones use atomic_inc_not_zero() and fail if we had
zero ->opened; in that case the file we are opening is doomed.
* have the inodes of dynamic files marked on removal (from the
callback of simple_recursive_removal()) - clear ->i_private there.
* have open of dynamic ones verify they hadn't been already removed,
along with checking that state is FFS_ACTIVE. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/smaps: fix race between smaps_hugetlb_range and migration
smaps_hugetlb_range() handles the pte without holdling ptl, and may be
concurrenct with migration, leaing to BUG_ON in pfn_swap_entry_to_page().
The race is as follows.
smaps_hugetlb_range migrate_pages
huge_ptep_get
remove_migration_ptes
folio_unlock
pfn_swap_entry_folio
BUG_ON
To fix it, hold ptl lock in smaps_hugetlb_range(). |
| In the Linux kernel, the following vulnerability has been resolved:
s390/ism: fix concurrency management in ism_cmd()
The s390x ISM device data sheet clearly states that only one
request-response sequence is allowable per ISM function at any point in
time. Unfortunately as of today the s390/ism driver in Linux does not
honor that requirement. This patch aims to rectify that.
This problem was discovered based on Aliaksei's bug report which states
that for certain workloads the ISM functions end up entering error state
(with PEC 2 as seen from the logs) after a while and as a consequence
connections handled by the respective function break, and for future
connection requests the ISM device is not considered -- given it is in a
dysfunctional state. During further debugging PEC 3A was observed as
well.
A kernel message like
[ 1211.244319] zpci: 061a:00:00.0: Event 0x2 reports an error for PCI function 0x61a
is a reliable indicator of the stated function entering error state
with PEC 2. Let me also point out that a kernel message like
[ 1211.244325] zpci: 061a:00:00.0: The ism driver bound to the device does not support error recovery
is a reliable indicator that the ISM function won't be auto-recovered
because the ISM driver currently lacks support for it.
On a technical level, without this synchronization, commands (inputs to
the FW) may be partially or fully overwritten (corrupted) by another CPU
trying to issue commands on the same function. There is hard evidence that
this can lead to DMB token values being used as DMB IOVAs, leading to
PEC 2 PCI events indicating invalid DMA. But this is only one of the
failure modes imaginable. In theory even completely losing one command
and executing another one twice and then trying to interpret the outputs
as if the command we intended to execute was actually executed and not
the other one is also possible. Frankly, I don't feel confident about
providing an exhaustive list of possible consequences. |
| In the Linux kernel, the following vulnerability has been resolved:
pinmux: fix race causing mux_owner NULL with active mux_usecount
commit 5a3e85c3c397 ("pinmux: Use sequential access to access
desc->pinmux data") tried to address the issue when two client of the
same gpio calls pinctrl_select_state() for the same functionality, was
resulting in NULL pointer issue while accessing desc->mux_owner.
However, issue was not completely fixed due to the way it was handled
and it can still result in the same NULL pointer.
The issue occurs due to the following interleaving:
cpu0 (process A) cpu1 (process B)
pin_request() { pin_free() {
mutex_lock()
desc->mux_usecount--; //becomes 0
..
mutex_unlock()
mutex_lock(desc->mux)
desc->mux_usecount++; // becomes 1
desc->mux_owner = owner;
mutex_unlock(desc->mux)
mutex_lock(desc->mux)
desc->mux_owner = NULL;
mutex_unlock(desc->mux)
This sequence leads to a state where the pin appears to be in use
(`mux_usecount == 1`) but has no owner (`mux_owner == NULL`), which can
cause NULL pointer on next pin_request on the same pin.
Ensure that updates to mux_usecount and mux_owner are performed
atomically under the same lock. Only clear mux_owner when mux_usecount
reaches zero and no new owner has been assigned. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix block group refcount race in btrfs_create_pending_block_groups()
Block group creation is done in two phases, which results in a slightly
unintuitive property: a block group can be allocated/deallocated from
after btrfs_make_block_group() adds it to the space_info with
btrfs_add_bg_to_space_info(), but before creation is completely completed
in btrfs_create_pending_block_groups(). As a result, it is possible for a
block group to go unused and have 'btrfs_mark_bg_unused' called on it
concurrently with 'btrfs_create_pending_block_groups'. This causes a
number of issues, which were fixed with the block group flag
'BLOCK_GROUP_FLAG_NEW'.
However, this fix is not quite complete. Since it does not use the
unused_bg_lock, it is possible for the following race to occur:
btrfs_create_pending_block_groups btrfs_mark_bg_unused
if list_empty // false
list_del_init
clear_bit
else if (test_bit) // true
list_move_tail
And we get into the exact same broken ref count and invalid new_bgs
state for transaction cleanup that BLOCK_GROUP_FLAG_NEW was designed to
prevent.
The broken refcount aspect will result in a warning like:
[1272.943527] refcount_t: underflow; use-after-free.
[1272.943967] WARNING: CPU: 1 PID: 61 at lib/refcount.c:28 refcount_warn_saturate+0xba/0x110
[1272.944731] Modules linked in: btrfs virtio_net xor zstd_compress raid6_pq null_blk [last unloaded: btrfs]
[1272.945550] CPU: 1 UID: 0 PID: 61 Comm: kworker/u32:1 Kdump: loaded Tainted: G W 6.14.0-rc5+ #108
[1272.946368] Tainted: [W]=WARN
[1272.946585] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[1272.947273] Workqueue: btrfs_discard btrfs_discard_workfn [btrfs]
[1272.947788] RIP: 0010:refcount_warn_saturate+0xba/0x110
[1272.949532] RSP: 0018:ffffbf1200247df0 EFLAGS: 00010282
[1272.949901] RAX: 0000000000000000 RBX: ffffa14b00e3f800 RCX: 0000000000000000
[1272.950437] RDX: 0000000000000000 RSI: ffffbf1200247c78 RDI: 00000000ffffdfff
[1272.950986] RBP: ffffa14b00dc2860 R08: 00000000ffffdfff R09: ffffffff90526268
[1272.951512] R10: ffffffff904762c0 R11: 0000000063666572 R12: ffffa14b00dc28c0
[1272.952024] R13: 0000000000000000 R14: ffffa14b00dc2868 R15: 000001285dcd12c0
[1272.952850] FS: 0000000000000000(0000) GS:ffffa14d33c40000(0000) knlGS:0000000000000000
[1272.953458] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1272.953931] CR2: 00007f838cbda000 CR3: 000000010104e000 CR4: 00000000000006f0
[1272.954474] Call Trace:
[1272.954655] <TASK>
[1272.954812] ? refcount_warn_saturate+0xba/0x110
[1272.955173] ? __warn.cold+0x93/0xd7
[1272.955487] ? refcount_warn_saturate+0xba/0x110
[1272.955816] ? report_bug+0xe7/0x120
[1272.956103] ? handle_bug+0x53/0x90
[1272.956424] ? exc_invalid_op+0x13/0x60
[1272.956700] ? asm_exc_invalid_op+0x16/0x20
[1272.957011] ? refcount_warn_saturate+0xba/0x110
[1272.957399] btrfs_discard_cancel_work.cold+0x26/0x2b [btrfs]
[1272.957853] btrfs_put_block_group.cold+0x5d/0x8e [btrfs]
[1272.958289] btrfs_discard_workfn+0x194/0x380 [btrfs]
[1272.958729] process_one_work+0x130/0x290
[1272.959026] worker_thread+0x2ea/0x420
[1272.959335] ? __pfx_worker_thread+0x10/0x10
[1272.959644] kthread+0xd7/0x1c0
[1272.959872] ? __pfx_kthread+0x10/0x10
[1272.960172] ret_from_fork+0x30/0x50
[1272.960474] ? __pfx_kthread+0x10/0x10
[1272.960745] ret_from_fork_asm+0x1a/0x30
[1272.961035] </TASK>
[1272.961238] ---[ end trace 0000000000000000 ]---
Though we have seen them in the async discard workfn as well. It is
most likely to happen after a relocation finishes which cancels discard,
tears down the block group, etc.
Fix this fully by taking the lock arou
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix the recovery flow of the UMR QP
This patch addresses an issue in the recovery flow of the UMR QP,
ensuring tasks do not get stuck, as highlighted by the call trace [1].
During recovery, before transitioning the QP to the RESET state, the
software must wait for all outstanding WRs to complete.
Failing to do so can cause the firmware to skip sending some flushed
CQEs with errors and simply discard them upon the RESET, as per the IB
specification.
This race condition can result in lost CQEs and tasks becoming stuck.
To resolve this, the patch sends a final WR which serves only as a
barrier before moving the QP state to RESET.
Once a CQE is received for that final WR, it guarantees that no
outstanding WRs remain, making it safe to transition the QP to RESET and
subsequently back to RTS, restoring proper functionality.
Note:
For the barrier WR, we simply reuse the failed and ready WR.
Since the QP is in an error state, it will only receive
IB_WC_WR_FLUSH_ERR. However, as it serves only as a barrier we don't
care about its status.
[1]
INFO: task rdma_resource_l:1922 blocked for more than 120 seconds.
Tainted: G W 6.12.0-rc7+ #1626
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:rdma_resource_l state:D stack:0 pid:1922 tgid:1922 ppid:1369
flags:0x00004004
Call Trace:
<TASK>
__schedule+0x420/0xd30
schedule+0x47/0x130
schedule_timeout+0x280/0x300
? mark_held_locks+0x48/0x80
? lockdep_hardirqs_on_prepare+0xe5/0x1a0
wait_for_completion+0x75/0x130
mlx5r_umr_post_send_wait+0x3c2/0x5b0 [mlx5_ib]
? __pfx_mlx5r_umr_done+0x10/0x10 [mlx5_ib]
mlx5r_umr_revoke_mr+0x93/0xc0 [mlx5_ib]
__mlx5_ib_dereg_mr+0x299/0x520 [mlx5_ib]
? _raw_spin_unlock_irq+0x24/0x40
? wait_for_completion+0xfe/0x130
? rdma_restrack_put+0x63/0xe0 [ib_core]
ib_dereg_mr_user+0x5f/0x120 [ib_core]
? lock_release+0xc6/0x280
destroy_hw_idr_uobject+0x1d/0x60 [ib_uverbs]
uverbs_destroy_uobject+0x58/0x1d0 [ib_uverbs]
uobj_destroy+0x3f/0x70 [ib_uverbs]
ib_uverbs_cmd_verbs+0x3e4/0xbb0 [ib_uverbs]
? __pfx_uverbs_destroy_def_handler+0x10/0x10 [ib_uverbs]
? __lock_acquire+0x64e/0x2080
? mark_held_locks+0x48/0x80
? find_held_lock+0x2d/0xa0
? lock_acquire+0xc1/0x2f0
? ib_uverbs_ioctl+0xcb/0x170 [ib_uverbs]
? __fget_files+0xc3/0x1b0
ib_uverbs_ioctl+0xe7/0x170 [ib_uverbs]
? ib_uverbs_ioctl+0xcb/0x170 [ib_uverbs]
__x64_sys_ioctl+0x1b0/0xa70
do_syscall_64+0x6b/0x140
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f99c918b17b
RSP: 002b:00007ffc766d0468 EFLAGS: 00000246 ORIG_RAX:
0000000000000010
RAX: ffffffffffffffda RBX: 00007ffc766d0578 RCX:
00007f99c918b17b
RDX: 00007ffc766d0560 RSI: 00000000c0181b01 RDI:
0000000000000003
RBP: 00007ffc766d0540 R08: 00007f99c8f99010 R09:
000000000000bd7e
R10: 00007f99c94c1c70 R11: 0000000000000246 R12:
00007ffc766d0530
R13: 000000000000001c R14: 0000000040246a80 R15:
0000000000000000
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix a race for an ODP MR which leads to CQE with error
This patch addresses a race condition for an ODP MR that can result in a
CQE with an error on the UMR QP.
During the __mlx5_ib_dereg_mr() flow, the following sequence of calls
occurs:
mlx5_revoke_mr()
mlx5r_umr_revoke_mr()
mlx5r_umr_post_send_wait()
At this point, the lkey is freed from the hardware's perspective.
However, concurrently, mlx5_ib_invalidate_range() might be triggered by
another task attempting to invalidate a range for the same freed lkey.
This task will:
- Acquire the umem_odp->umem_mutex lock.
- Call mlx5r_umr_update_xlt() on the UMR QP.
- Since the lkey has already been freed, this can lead to a CQE error,
causing the UMR QP to enter an error state [1].
To resolve this race condition, the umem_odp->umem_mutex lock is now also
acquired as part of the mlx5_revoke_mr() scope. Upon successful revoke,
we set umem_odp->private which points to that MR to NULL, preventing any
further invalidation attempts on its lkey.
[1] From dmesg:
infiniband rocep8s0f0: dump_cqe:277:(pid 0): WC error: 6, Message: memory bind operation error
cqe_dump: 00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
cqe_dump: 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
cqe_dump: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
cqe_dump: 00000030: 00 00 00 00 08 00 78 06 25 00 11 b9 00 0e dd d2
WARNING: CPU: 15 PID: 1506 at drivers/infiniband/hw/mlx5/umr.c:394 mlx5r_umr_post_send_wait+0x15a/0x2b0 [mlx5_ib]
Modules linked in: ip6table_mangle ip6table_natip6table_filter ip6_tables iptable_mangle xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi rdma_cm iw_cm ib_umad ib_ipoib ib_cm mlx5_ib ib_uverbs ib_core fuse mlx5_core
CPU: 15 UID: 0 PID: 1506 Comm: ibv_rc_pingpong Not tainted 6.12.0-rc7+ #1626
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:mlx5r_umr_post_send_wait+0x15a/0x2b0 [mlx5_ib]
[..]
Call Trace:
<TASK>
mlx5r_umr_update_xlt+0x23c/0x3e0 [mlx5_ib]
mlx5_ib_invalidate_range+0x2e1/0x330 [mlx5_ib]
__mmu_notifier_invalidate_range_start+0x1e1/0x240
zap_page_range_single+0xf1/0x1a0
madvise_vma_behavior+0x677/0x6e0
do_madvise+0x1a2/0x4b0
__x64_sys_madvise+0x25/0x30
do_syscall_64+0x6b/0x140
entry_SYSCALL_64_after_hwframe+0x76/0x7e |
| In the Linux kernel, the following vulnerability has been resolved:
udp: Deal with race between UDP socket address change and rehash
If a UDP socket changes its local address while it's receiving
datagrams, as a result of connect(), there is a period during which
a lookup operation might fail to find it, after the address is changed
but before the secondary hash (port and address) and the four-tuple
hash (local and remote ports and addresses) are updated.
Secondary hash chains were introduced by commit 30fff9231fad ("udp:
bind() optimisation") and, as a result, a rehash operation became
needed to make a bound socket reachable again after a connect().
This operation was introduced by commit 719f835853a9 ("udp: add
rehash on connect()") which isn't however a complete fix: the
socket will be found once the rehashing completes, but not while
it's pending.
This is noticeable with a socat(1) server in UDP4-LISTEN mode, and a
client sending datagrams to it. After the server receives the first
datagram (cf. _xioopen_ipdgram_listen()), it issues a connect() to
the address of the sender, in order to set up a directed flow.
Now, if the client, running on a different CPU thread, happens to
send a (subsequent) datagram while the server's socket changes its
address, but is not rehashed yet, this will result in a failed
lookup and a port unreachable error delivered to the client, as
apparent from the following reproducer:
LEN=$(($(cat /proc/sys/net/core/wmem_default) / 4))
dd if=/dev/urandom bs=1 count=${LEN} of=tmp.in
while :; do
taskset -c 1 socat UDP4-LISTEN:1337,null-eof OPEN:tmp.out,create,trunc &
sleep 0.1 || sleep 1
taskset -c 2 socat OPEN:tmp.in UDP4:localhost:1337,shut-null
wait
done
where the client will eventually get ECONNREFUSED on a write()
(typically the second or third one of a given iteration):
2024/11/13 21:28:23 socat[46901] E write(6, 0x556db2e3c000, 8192): Connection refused
This issue was first observed as a seldom failure in Podman's tests
checking UDP functionality while using pasta(1) to connect the
container's network namespace, which leads us to a reproducer with
the lookup error resulting in an ICMP packet on a tap device:
LOCAL_ADDR="$(ip -j -4 addr show|jq -rM '.[] | .addr_info[0] | select(.scope == "global").local')"
while :; do
./pasta --config-net -p pasta.pcap -u 1337 socat UDP4-LISTEN:1337,null-eof OPEN:tmp.out,create,trunc &
sleep 0.2 || sleep 1
socat OPEN:tmp.in UDP4:${LOCAL_ADDR}:1337,shut-null
wait
cmp tmp.in tmp.out
done
Once this fails:
tmp.in tmp.out differ: char 8193, line 29
we can finally have a look at what's going on:
$ tshark -r pasta.pcap
1 0.000000 :: ? ff02::16 ICMPv6 110 Multicast Listener Report Message v2
2 0.168690 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192
3 0.168767 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192
4 0.168806 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192
5 0.168827 c6:47:05:8d:dc:04 ? Broadcast ARP 42 Who has 88.198.0.161? Tell 88.198.0.164
6 0.168851 9a:55:9a:55:9a:55 ? c6:47:05:8d:dc:04 ARP 42 88.198.0.161 is at 9a:55:9a:55:9a:55
7 0.168875 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192
8 0.168896 88.198.0.164 ? 88.198.0.161 ICMP 590 Destination unreachable (Port unreachable)
9 0.168926 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192
10 0.168959 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192
11 0.168989 88.198.0.161 ? 88.198.0.164 UDP 4138 60260 ? 1337 Len=4096
12 0.169010 88.198.0.161 ? 88.198.0.164 UDP 42 60260 ? 1337 Len=0
On the third datagram received, the network namespace of the container
initiates an ARP lookup to deliver the ICMP message.
In another variant of this reproducer, starting the client with:
strace -f pasta --config-net -u 1337 socat UDP4-LISTEN:1337,null-eof OPEN:tmp.out,create,tru
---truncated--- |
