| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: Prevent race issues involving the adminq
There are multiple paths that can result in using the pdsc's
adminq.
[1] pdsc_adminq_isr and the resulting work from queue_work(),
i.e. pdsc_work_thread()->pdsc_process_adminq()
[2] pdsc_adminq_post()
When the device goes through reset via PCIe reset and/or
a fw_down/fw_up cycle due to bad PCIe state or bad device
state the adminq is destroyed and recreated.
A NULL pointer dereference can happen if [1] or [2] happens
after the adminq is already destroyed.
In order to fix this, add some further state checks and
implement reference counting for adminq uses. Reference
counting was used because multiple threads can attempt to
access the adminq at the same time via [1] or [2]. Additionally,
multiple clients (i.e. pds-vfio-pci) can be using [2]
at the same time.
The adminq_refcnt is initialized to 1 when the adminq has been
allocated and is ready to use. Users/clients of the adminq
(i.e. [1] and [2]) will increment the refcnt when they are using
the adminq. When the driver goes into a fw_down cycle it will
set the PDSC_S_FW_DEAD bit and then wait for the adminq_refcnt
to hit 1. Setting the PDSC_S_FW_DEAD before waiting will prevent
any further adminq_refcnt increments. Waiting for the
adminq_refcnt to hit 1 allows for any current users of the adminq
to finish before the driver frees the adminq. Once the
adminq_refcnt hits 1 the driver clears the refcnt to signify that
the adminq is deleted and cannot be used. On the fw_up cycle the
driver will once again initialize the adminq_refcnt to 1 allowing
the adminq to be used again. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: huge_memory: don't force huge page alignment on 32 bit
commit efa7df3e3bb5 ("mm: align larger anonymous mappings on THP
boundaries") caused two issues [1] [2] reported on 32 bit system or compat
userspace.
It doesn't make too much sense to force huge page alignment on 32 bit
system due to the constrained virtual address space.
[1] https://lore.kernel.org/linux-mm/d0a136a0-4a31-46bc-adf4-2db109a61672@kernel.org/
[2] https://lore.kernel.org/linux-mm/CAJuCfpHXLdQy1a2B6xN2d7quTYwg2OoZseYPZTRpU0eHHKD-sQ@mail.gmail.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
s390/vfio-ap: always filter entire AP matrix
The vfio_ap_mdev_filter_matrix function is called whenever a new adapter or
domain is assigned to the mdev. The purpose of the function is to update
the guest's AP configuration by filtering the matrix of adapters and
domains assigned to the mdev. When an adapter or domain is assigned, only
the APQNs associated with the APID of the new adapter or APQI of the new
domain are inspected. If an APQN does not reference a queue device bound to
the vfio_ap device driver, then it's APID will be filtered from the mdev's
matrix when updating the guest's AP configuration.
Inspecting only the APID of the new adapter or APQI of the new domain will
result in passing AP queues through to a guest that are not bound to the
vfio_ap device driver under certain circumstances. Consider the following:
guest's AP configuration (all also assigned to the mdev's matrix):
14.0004
14.0005
14.0006
16.0004
16.0005
16.0006
unassign domain 4
unbind queue 16.0005
assign domain 4
When domain 4 is re-assigned, since only domain 4 will be inspected, the
APQNs that will be examined will be:
14.0004
16.0004
Since both of those APQNs reference queue devices that are bound to the
vfio_ap device driver, nothing will get filtered from the mdev's matrix
when updating the guest's AP configuration. Consequently, queue 16.0005
will get passed through despite not being bound to the driver. This
violates the linux device model requirement that a guest shall only be
given access to devices bound to the device driver facilitating their
pass-through.
To resolve this problem, every adapter and domain assigned to the mdev will
be inspected when filtering the mdev's matrix. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/proc/task_mmu: move mmu notification mechanism inside mm lock
Move mmu notification mechanism inside mm lock to prevent race condition
in other components which depend on it. The notifier will invalidate
memory range. Depending upon the number of iterations, different memory
ranges would be invalidated.
The following warning would be removed by this patch:
WARNING: CPU: 0 PID: 5067 at arch/x86/kvm/../../../virt/kvm/kvm_main.c:734 kvm_mmu_notifier_change_pte+0x860/0x960 arch/x86/kvm/../../../virt/kvm/kvm_main.c:734
There is no behavioural and performance change with this patch when
there is no component registered with the mmu notifier.
[akpm@linux-foundation.org: narrow the scope of `range', per Sean] |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: make sure init the accept_queue's spinlocks once
When I run syz's reproduction C program locally, it causes the following
issue:
pvqspinlock: lock 0xffff9d181cd5c660 has corrupted value 0x0!
WARNING: CPU: 19 PID: 21160 at __pv_queued_spin_unlock_slowpath (kernel/locking/qspinlock_paravirt.h:508)
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:__pv_queued_spin_unlock_slowpath (kernel/locking/qspinlock_paravirt.h:508)
Code: 73 56 3a ff 90 c3 cc cc cc cc 8b 05 bb 1f 48 01 85 c0 74 05 c3 cc cc cc cc 8b 17 48 89 fe 48 c7 c7
30 20 ce 8f e8 ad 56 42 ff <0f> 0b c3 cc cc cc cc 0f 0b 0f 1f 40 00 90 90 90 90 90 90 90 90 90
RSP: 0018:ffffa8d200604cb8 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff9d1ef60e0908
RDX: 00000000ffffffd8 RSI: 0000000000000027 RDI: ffff9d1ef60e0900
RBP: ffff9d181cd5c280 R08: 0000000000000000 R09: 00000000ffff7fff
R10: ffffa8d200604b68 R11: ffffffff907dcdc8 R12: 0000000000000000
R13: ffff9d181cd5c660 R14: ffff9d1813a3f330 R15: 0000000000001000
FS: 00007fa110184640(0000) GS:ffff9d1ef60c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000000 CR3: 000000011f65e000 CR4: 00000000000006f0
Call Trace:
<IRQ>
_raw_spin_unlock (kernel/locking/spinlock.c:186)
inet_csk_reqsk_queue_add (net/ipv4/inet_connection_sock.c:1321)
inet_csk_complete_hashdance (net/ipv4/inet_connection_sock.c:1358)
tcp_check_req (net/ipv4/tcp_minisocks.c:868)
tcp_v4_rcv (net/ipv4/tcp_ipv4.c:2260)
ip_protocol_deliver_rcu (net/ipv4/ip_input.c:205)
ip_local_deliver_finish (net/ipv4/ip_input.c:234)
__netif_receive_skb_one_core (net/core/dev.c:5529)
process_backlog (./include/linux/rcupdate.h:779)
__napi_poll (net/core/dev.c:6533)
net_rx_action (net/core/dev.c:6604)
__do_softirq (./arch/x86/include/asm/jump_label.h:27)
do_softirq (kernel/softirq.c:454 kernel/softirq.c:441)
</IRQ>
<TASK>
__local_bh_enable_ip (kernel/softirq.c:381)
__dev_queue_xmit (net/core/dev.c:4374)
ip_finish_output2 (./include/net/neighbour.h:540 net/ipv4/ip_output.c:235)
__ip_queue_xmit (net/ipv4/ip_output.c:535)
__tcp_transmit_skb (net/ipv4/tcp_output.c:1462)
tcp_rcv_synsent_state_process (net/ipv4/tcp_input.c:6469)
tcp_rcv_state_process (net/ipv4/tcp_input.c:6657)
tcp_v4_do_rcv (net/ipv4/tcp_ipv4.c:1929)
__release_sock (./include/net/sock.h:1121 net/core/sock.c:2968)
release_sock (net/core/sock.c:3536)
inet_wait_for_connect (net/ipv4/af_inet.c:609)
__inet_stream_connect (net/ipv4/af_inet.c:702)
inet_stream_connect (net/ipv4/af_inet.c:748)
__sys_connect (./include/linux/file.h:45 net/socket.c:2064)
__x64_sys_connect (net/socket.c:2073 net/socket.c:2070 net/socket.c:2070)
do_syscall_64 (arch/x86/entry/common.c:51 arch/x86/entry/common.c:82)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:129)
RIP: 0033:0x7fa10ff05a3d
Code: 5b 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89
c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d ab a3 0e 00 f7 d8 64 89 01 48
RSP: 002b:00007fa110183de8 EFLAGS: 00000202 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000020000054 RCX: 00007fa10ff05a3d
RDX: 000000000000001c RSI: 0000000020000040 RDI: 0000000000000003
RBP: 00007fa110183e20 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000202 R12: 00007fa110184640
R13: 0000000000000000 R14: 00007fa10fe8b060 R15: 00007fff73e23b20
</TASK>
The issue triggering process is analyzed as follows:
Thread A Thread B
tcp_v4_rcv //receive ack TCP packet inet_shutdown
tcp_check_req tcp_disconnect //disconnect sock
... tcp_set_state(sk, TCP_CLOSE)
inet_csk_complete_hashdance ...
inet_csk_reqsk_queue_add
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
xsk: fix usage of multi-buffer BPF helpers for ZC XDP
Currently when packet is shrunk via bpf_xdp_adjust_tail() and memory
type is set to MEM_TYPE_XSK_BUFF_POOL, null ptr dereference happens:
[1136314.192256] BUG: kernel NULL pointer dereference, address:
0000000000000034
[1136314.203943] #PF: supervisor read access in kernel mode
[1136314.213768] #PF: error_code(0x0000) - not-present page
[1136314.223550] PGD 0 P4D 0
[1136314.230684] Oops: 0000 [#1] PREEMPT SMP NOPTI
[1136314.239621] CPU: 8 PID: 54203 Comm: xdpsock Not tainted 6.6.0+ #257
[1136314.250469] Hardware name: Intel Corporation S2600WFT/S2600WFT,
BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019
[1136314.265615] RIP: 0010:__xdp_return+0x6c/0x210
[1136314.274653] Code: ad 00 48 8b 47 08 49 89 f8 a8 01 0f 85 9b 01 00 00 0f 1f 44 00 00 f0 41 ff 48 34 75 32 4c 89 c7 e9 79 cd 80 ff 83 fe 03 75 17 <f6> 41 34 01 0f 85 02 01 00 00 48 89 cf e9 22 cc 1e 00 e9 3d d2 86
[1136314.302907] RSP: 0018:ffffc900089f8db0 EFLAGS: 00010246
[1136314.312967] RAX: ffffc9003168aed0 RBX: ffff8881c3300000 RCX:
0000000000000000
[1136314.324953] RDX: 0000000000000000 RSI: 0000000000000003 RDI:
ffffc9003168c000
[1136314.336929] RBP: 0000000000000ae0 R08: 0000000000000002 R09:
0000000000010000
[1136314.348844] R10: ffffc9000e495000 R11: 0000000000000040 R12:
0000000000000001
[1136314.360706] R13: 0000000000000524 R14: ffffc9003168aec0 R15:
0000000000000001
[1136314.373298] FS: 00007f8df8bbcb80(0000) GS:ffff8897e0e00000(0000)
knlGS:0000000000000000
[1136314.386105] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1136314.396532] CR2: 0000000000000034 CR3: 00000001aa912002 CR4:
00000000007706f0
[1136314.408377] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[1136314.420173] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:
0000000000000400
[1136314.431890] PKRU: 55555554
[1136314.439143] Call Trace:
[1136314.446058] <IRQ>
[1136314.452465] ? __die+0x20/0x70
[1136314.459881] ? page_fault_oops+0x15b/0x440
[1136314.468305] ? exc_page_fault+0x6a/0x150
[1136314.476491] ? asm_exc_page_fault+0x22/0x30
[1136314.484927] ? __xdp_return+0x6c/0x210
[1136314.492863] bpf_xdp_adjust_tail+0x155/0x1d0
[1136314.501269] bpf_prog_ccc47ae29d3b6570_xdp_sock_prog+0x15/0x60
[1136314.511263] ice_clean_rx_irq_zc+0x206/0xc60 [ice]
[1136314.520222] ? ice_xmit_zc+0x6e/0x150 [ice]
[1136314.528506] ice_napi_poll+0x467/0x670 [ice]
[1136314.536858] ? ttwu_do_activate.constprop.0+0x8f/0x1a0
[1136314.546010] __napi_poll+0x29/0x1b0
[1136314.553462] net_rx_action+0x133/0x270
[1136314.561619] __do_softirq+0xbe/0x28e
[1136314.569303] do_softirq+0x3f/0x60
This comes from __xdp_return() call with xdp_buff argument passed as
NULL which is supposed to be consumed by xsk_buff_free() call.
To address this properly, in ZC case, a node that represents the frag
being removed has to be pulled out of xskb_list. Introduce
appropriate xsk helpers to do such node operation and use them
accordingly within bpf_xdp_adjust_tail(). |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: regenerate buddy after block freeing failed if under fc replay
This mostly reverts commit 6bd97bf273bd ("ext4: remove redundant
mb_regenerate_buddy()") and reintroduces mb_regenerate_buddy(). Based on
code in mb_free_blocks(), fast commit replay can end up marking as free
blocks that are already marked as such. This causes corruption of the
buddy bitmap so we need to regenerate it in that case. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: vgic-its: Avoid potential UAF in LPI translation cache
There is a potential UAF scenario in the case of an LPI translation
cache hit racing with an operation that invalidates the cache, such
as a DISCARD ITS command. The root of the problem is that
vgic_its_check_cache() does not elevate the refcount on the vgic_irq
before dropping the lock that serializes refcount changes.
Have vgic_its_check_cache() raise the refcount on the returned vgic_irq
and add the corresponding decrement after queueing the interrupt. |
| In the Linux kernel, the following vulnerability has been resolved:
net: qualcomm: rmnet: fix global oob in rmnet_policy
The variable rmnet_link_ops assign a *bigger* maxtype which leads to a
global out-of-bounds read when parsing the netlink attributes. See bug
trace below:
==================================================================
BUG: KASAN: global-out-of-bounds in validate_nla lib/nlattr.c:386 [inline]
BUG: KASAN: global-out-of-bounds in __nla_validate_parse+0x24af/0x2750 lib/nlattr.c:600
Read of size 1 at addr ffffffff92c438d0 by task syz-executor.6/84207
CPU: 0 PID: 84207 Comm: syz-executor.6 Tainted: G N 6.1.0 #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x8b/0xb3 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:284 [inline]
print_report+0x172/0x475 mm/kasan/report.c:395
kasan_report+0xbb/0x1c0 mm/kasan/report.c:495
validate_nla lib/nlattr.c:386 [inline]
__nla_validate_parse+0x24af/0x2750 lib/nlattr.c:600
__nla_parse+0x3e/0x50 lib/nlattr.c:697
nla_parse_nested_deprecated include/net/netlink.h:1248 [inline]
__rtnl_newlink+0x50a/0x1880 net/core/rtnetlink.c:3485
rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3594
rtnetlink_rcv_msg+0x43c/0xd70 net/core/rtnetlink.c:6091
netlink_rcv_skb+0x14f/0x410 net/netlink/af_netlink.c:2540
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x54e/0x800 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x930/0xe50 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0x154/0x190 net/socket.c:734
____sys_sendmsg+0x6df/0x840 net/socket.c:2482
___sys_sendmsg+0x110/0x1b0 net/socket.c:2536
__sys_sendmsg+0xf3/0x1c0 net/socket.c:2565
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7fdcf2072359
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 f1 19 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fdcf13e3168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007fdcf219ff80 RCX: 00007fdcf2072359
RDX: 0000000000000000 RSI: 0000000020000200 RDI: 0000000000000003
RBP: 00007fdcf20bd493 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fffbb8d7bdf R14: 00007fdcf13e3300 R15: 0000000000022000
</TASK>
The buggy address belongs to the variable:
rmnet_policy+0x30/0xe0
The buggy address belongs to the physical page:
page:0000000065bdeb3c refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x155243
flags: 0x200000000001000(reserved|node=0|zone=2)
raw: 0200000000001000 ffffea00055490c8 ffffea00055490c8 0000000000000000
raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffffffff92c43780: f9 f9 f9 f9 00 00 00 02 f9 f9 f9 f9 00 00 00 07
ffffffff92c43800: f9 f9 f9 f9 00 00 00 05 f9 f9 f9 f9 06 f9 f9 f9
>ffffffff92c43880: f9 f9 f9 f9 00 00 00 00 00 00 f9 f9 f9 f9 f9 f9
^
ffffffff92c43900: 00 00 00 00 00 00 00 00 07 f9 f9 f9 f9 f9 f9 f9
ffffffff92c43980: 00 00 00 07 f9 f9 f9 f9 00 00 00 05 f9 f9 f9 f9
According to the comment of `nla_parse_nested_deprecated`, the maxtype
should be len(destination array) - 1. Hence use `IFLA_RMNET_MAX` here. |
| In the Linux kernel, the following vulnerability has been resolved:
mlxsw: spectrum_acl_tcam: Fix stack corruption
When tc filters are first added to a net device, the corresponding local
port gets bound to an ACL group in the device. The group contains a list
of ACLs. In turn, each ACL points to a different TCAM region where the
filters are stored. During forwarding, the ACLs are sequentially
evaluated until a match is found.
One reason to place filters in different regions is when they are added
with decreasing priorities and in an alternating order so that two
consecutive filters can never fit in the same region because of their
key usage.
In Spectrum-2 and newer ASICs the firmware started to report that the
maximum number of ACLs in a group is more than 16, but the layout of the
register that configures ACL groups (PAGT) was not updated to account
for that. It is therefore possible to hit stack corruption [1] in the
rare case where more than 16 ACLs in a group are required.
Fix by limiting the maximum ACL group size to the minimum between what
the firmware reports and the maximum ACLs that fit in the PAGT register.
Add a test case to make sure the machine does not crash when this
condition is hit.
[1]
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120
[...]
dump_stack_lvl+0x36/0x50
panic+0x305/0x330
__stack_chk_fail+0x15/0x20
mlxsw_sp_acl_tcam_group_update+0x116/0x120
mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110
mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20
mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0
mlxsw_sp_acl_rule_add+0x47/0x240
mlxsw_sp_flower_replace+0x1a9/0x1d0
tc_setup_cb_add+0xdc/0x1c0
fl_hw_replace_filter+0x146/0x1f0
fl_change+0xc17/0x1360
tc_new_tfilter+0x472/0xb90
rtnetlink_rcv_msg+0x313/0x3b0
netlink_rcv_skb+0x58/0x100
netlink_unicast+0x244/0x390
netlink_sendmsg+0x1e4/0x440
____sys_sendmsg+0x164/0x260
___sys_sendmsg+0x9a/0xe0
__sys_sendmsg+0x7a/0xc0
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x63/0x6b |
| In the Linux kernel, the following vulnerability has been resolved:
misc: pci_endpoint_test: Free IRQs before removing the device
In pci_endpoint_test_remove(), freeing the IRQs after removing the device
creates a small race window for IRQs to be received with the test device
memory already released, causing the IRQ handler to access invalid memory,
resulting in an oops.
Free the device IRQs before removing the device to avoid this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: qat - fix out-of-bounds read
When preparing an AER-CTR request, the driver copies the key provided by
the user into a data structure that is accessible by the firmware.
If the target device is QAT GEN4, the key size is rounded up by 16 since
a rounded up size is expected by the device.
If the key size is rounded up before the copy, the size used for copying
the key might be bigger than the size of the region containing the key,
causing an out-of-bounds read.
Fix by doing the copy first and then update the keylen.
This is to fix the following warning reported by KASAN:
[ 138.150574] BUG: KASAN: global-out-of-bounds in qat_alg_skcipher_init_com.isra.0+0x197/0x250 [intel_qat]
[ 138.150641] Read of size 32 at addr ffffffff88c402c0 by task cryptomgr_test/2340
[ 138.150651] CPU: 15 PID: 2340 Comm: cryptomgr_test Not tainted 6.2.0-rc1+ #45
[ 138.150659] Hardware name: Intel Corporation ArcherCity/ArcherCity, BIOS EGSDCRB1.86B.0087.D13.2208261706 08/26/2022
[ 138.150663] Call Trace:
[ 138.150668] <TASK>
[ 138.150922] kasan_check_range+0x13a/0x1c0
[ 138.150931] memcpy+0x1f/0x60
[ 138.150940] qat_alg_skcipher_init_com.isra.0+0x197/0x250 [intel_qat]
[ 138.151006] qat_alg_skcipher_init_sessions+0xc1/0x240 [intel_qat]
[ 138.151073] crypto_skcipher_setkey+0x82/0x160
[ 138.151085] ? prepare_keybuf+0xa2/0xd0
[ 138.151095] test_skcipher_vec_cfg+0x2b8/0x800 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: message: mptlan: Fix use after free bug in mptlan_remove() due to race condition
mptlan_probe() calls mpt_register_lan_device() which initializes the
&priv->post_buckets_task workqueue. A call to
mpt_lan_wake_post_buckets_task() will subsequently start the work.
During driver unload in mptlan_remove() the following race may occur:
CPU0 CPU1
|mpt_lan_post_receive_buckets_work()
mptlan_remove() |
free_netdev() |
kfree(dev); |
|
| dev->mtu
| //use
Fix this by finishing the work prior to cleaning up in mptlan_remove().
[mkp: we really should remove mptlan instead of attempting to fix it] |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Disable preemption in bpf_perf_event_output
The nesting protection in bpf_perf_event_output relies on disabled
preemption, which is guaranteed for kprobes and tracepoints.
However bpf_perf_event_output can be also called from uprobes context
through bpf_prog_run_array_sleepable function which disables migration,
but keeps preemption enabled.
This can cause task to be preempted by another one inside the nesting
protection and lead eventually to two tasks using same perf_sample_data
buffer and cause crashes like:
kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
BUG: unable to handle page fault for address: ffffffff82be3eea
...
Call Trace:
? __die+0x1f/0x70
? page_fault_oops+0x176/0x4d0
? exc_page_fault+0x132/0x230
? asm_exc_page_fault+0x22/0x30
? perf_output_sample+0x12b/0x910
? perf_event_output+0xd0/0x1d0
? bpf_perf_event_output+0x162/0x1d0
? bpf_prog_c6271286d9a4c938_krava1+0x76/0x87
? __uprobe_perf_func+0x12b/0x540
? uprobe_dispatcher+0x2c4/0x430
? uprobe_notify_resume+0x2da/0xce0
? atomic_notifier_call_chain+0x7b/0x110
? exit_to_user_mode_prepare+0x13e/0x290
? irqentry_exit_to_user_mode+0x5/0x30
? asm_exc_int3+0x35/0x40
Fixing this by disabling preemption in bpf_perf_event_output. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: dvm: Fix memcpy: detected field-spanning write backtrace
A received TKIP key may be up to 32 bytes because it may contain
MIC rx/tx keys too. These are not used by iwl and copying these
over overflows the iwl_keyinfo.key field.
Add a check to not copy more data to iwl_keyinfo.key then will fit.
This fixes backtraces like this one:
memcpy: detected field-spanning write (size 32) of single field "sta_cmd.key.key" at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 (size 16)
WARNING: CPU: 1 PID: 946 at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 iwlagn_send_sta_key+0x375/0x390 [iwldvm]
<snip>
Hardware name: Dell Inc. Latitude E6430/0H3MT5, BIOS A21 05/08/2017
RIP: 0010:iwlagn_send_sta_key+0x375/0x390 [iwldvm]
<snip>
Call Trace:
<TASK>
iwl_set_dynamic_key+0x1f0/0x220 [iwldvm]
iwlagn_mac_set_key+0x1e4/0x280 [iwldvm]
drv_set_key+0xa4/0x1b0 [mac80211]
ieee80211_key_enable_hw_accel+0xa8/0x2d0 [mac80211]
ieee80211_key_replace+0x22d/0x8e0 [mac80211]
<snip> |
| In the Linux kernel, the following vulnerability has been resolved:
media: av7110: prevent underflow in write_ts_to_decoder()
The buf[4] value comes from the user via ts_play(). It is a value in
the u8 range. The final length we pass to av7110_ipack_instant_repack()
is "len - (buf[4] + 1) - 4" so add a check to ensure that the length is
not negative. It's not clear that passing a negative len value does
anything bad necessarily, but it's not best practice.
With the new bounds checking the "if (!len)" condition is no longer
possible or required so remove that. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: avoid out of bounds access in decode_preauth_ctxt()
Confirm that the accessed pneg_ctxt->HashAlgorithms address sits within
the SMB request boundary; deassemble_neg_contexts() only checks that the
eight byte smb2_neg_context header + (client controlled) DataLength are
within the packet boundary, which is insufficient.
Checking for sizeof(struct smb2_preauth_neg_context) is overkill given
that the type currently assumes SMB311_SALT_SIZE bytes of trailing Salt. |
| In the Linux kernel, the following vulnerability has been resolved:
Revert "IB/isert: Fix incorrect release of isert connection"
Commit: 699826f4e30a ("IB/isert: Fix incorrect release of isert connection") is
causing problems on OPA when DEVICE_REMOVAL is happening.
------------[ cut here ]------------
WARNING: CPU: 52 PID: 2117247 at drivers/infiniband/core/cq.c:359
ib_cq_pool_cleanup+0xac/0xb0 [ib_core]
Modules linked in: nfsd nfs_acl target_core_user uio tcm_fc libfc
scsi_transport_fc tcm_loop target_core_pscsi target_core_iblock target_core_file
rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs
rfkill rpcrdma rdma_ucm ib_srpt sunrpc ib_isert iscsi_target_mod target_core_mod
opa_vnic ib_iser libiscsi ib_umad scsi_transport_iscsi rdma_cm ib_ipoib iw_cm
ib_cm hfi1(-) rdmavt ib_uverbs intel_rapl_msr intel_rapl_common sb_edac ib_core
x86_pkg_temp_thermal intel_powerclamp coretemp i2c_i801 mxm_wmi rapl iTCO_wdt
ipmi_si iTCO_vendor_support mei_me ipmi_devintf mei intel_cstate ioatdma
intel_uncore i2c_smbus joydev pcspkr lpc_ich ipmi_msghandler acpi_power_meter
acpi_pad xfs libcrc32c sr_mod sd_mod cdrom t10_pi sg crct10dif_pclmul
crc32_pclmul crc32c_intel drm_kms_helper drm_shmem_helper ahci libahci
ghash_clmulni_intel igb drm libata dca i2c_algo_bit wmi fuse
CPU: 52 PID: 2117247 Comm: modprobe Not tainted 6.5.0-rc1+ #1
Hardware name: Intel Corporation S2600CWR/S2600CW, BIOS
SE5C610.86B.01.01.0014.121820151719 12/18/2015
RIP: 0010:ib_cq_pool_cleanup+0xac/0xb0 [ib_core]
Code: ff 48 8b 43 40 48 8d 7b 40 48 83 e8 40 4c 39 e7 75 b3 49 83
c4 10 4d 39 fc 75 94 5b 5d 41 5c 41 5d 41 5e 41 5f c3 cc cc cc cc <0f> 0b eb a1
90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f
RSP: 0018:ffffc10bea13fc80 EFLAGS: 00010206
RAX: 000000000000010c RBX: ffff9bf5c7e66c00 RCX: 000000008020001d
RDX: 000000008020001e RSI: fffff175221f9900 RDI: ffff9bf5c7e67640
RBP: ffff9bf5c7e67600 R08: ffff9bf5c7e64400 R09: 000000008020001d
R10: 0000000040000000 R11: 0000000000000000 R12: ffff9bee4b1e8a18
R13: dead000000000122 R14: dead000000000100 R15: ffff9bee4b1e8a38
FS: 00007ff1e6d38740(0000) GS:ffff9bfd9fb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005652044ecc68 CR3: 0000000889b5c005 CR4: 00000000001706e0
Call Trace:
<TASK>
? __warn+0x80/0x130
? ib_cq_pool_cleanup+0xac/0xb0 [ib_core]
? report_bug+0x195/0x1a0
? handle_bug+0x3c/0x70
? exc_invalid_op+0x14/0x70
? asm_exc_invalid_op+0x16/0x20
? ib_cq_pool_cleanup+0xac/0xb0 [ib_core]
disable_device+0x9d/0x160 [ib_core]
__ib_unregister_device+0x42/0xb0 [ib_core]
ib_unregister_device+0x22/0x30 [ib_core]
rvt_unregister_device+0x20/0x90 [rdmavt]
hfi1_unregister_ib_device+0x16/0xf0 [hfi1]
remove_one+0x55/0x1a0 [hfi1]
pci_device_remove+0x36/0xa0
device_release_driver_internal+0x193/0x200
driver_detach+0x44/0x90
bus_remove_driver+0x69/0xf0
pci_unregister_driver+0x2a/0xb0
hfi1_mod_cleanup+0xc/0x3c [hfi1]
__do_sys_delete_module.constprop.0+0x17a/0x2f0
? exit_to_user_mode_prepare+0xc4/0xd0
? syscall_trace_enter.constprop.0+0x126/0x1a0
do_syscall_64+0x5c/0x90
? syscall_exit_to_user_mode+0x12/0x30
? do_syscall_64+0x69/0x90
? syscall_exit_work+0x103/0x130
? syscall_exit_to_user_mode+0x12/0x30
? do_syscall_64+0x69/0x90
? exc_page_fault+0x65/0x150
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
RIP: 0033:0x7ff1e643f5ab
Code: 73 01 c3 48 8b 0d 75 a8 1b 00 f7 d8 64 89 01 48 83 c8 ff c3
66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0
ff ff 73 01 c3 48 8b 0d 45 a8 1b 00 f7 d8 64 89 01 48
RSP: 002b:00007ffec9103cc8 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 00005615267fdc50 RCX: 00007ff1e643f5ab
RDX: 0000000000000000 RSI: 0000000000000800 RDI: 00005615267fdcb8
RBP: 00005615267fdc50 R08: 0000000000000000 R09: 0000000000000000
R10: 00007ff1e659eac0 R11: 0000000000000206 R12: 00005615267fdcb8
R13: 00000000000
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: TC, Fix using eswitch mapping in nic mode
Cited patch is using the eswitch object mapping pool while
in nic mode where it isn't initialized. This results in the
trace below [0].
Fix that by using either nic or eswitch object mapping pool
depending if eswitch is enabled or not.
[0]:
[ 826.446057] ==================================================================
[ 826.446729] BUG: KASAN: slab-use-after-free in mlx5_add_flow_rules+0x30/0x490 [mlx5_core]
[ 826.447515] Read of size 8 at addr ffff888194485830 by task tc/6233
[ 826.448243] CPU: 16 PID: 6233 Comm: tc Tainted: G W 6.3.0-rc6+ #1
[ 826.448890] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 826.449785] Call Trace:
[ 826.450052] <TASK>
[ 826.450302] dump_stack_lvl+0x33/0x50
[ 826.450650] print_report+0xc2/0x610
[ 826.450998] ? __virt_addr_valid+0xb1/0x130
[ 826.451385] ? mlx5_add_flow_rules+0x30/0x490 [mlx5_core]
[ 826.451935] kasan_report+0xae/0xe0
[ 826.452276] ? mlx5_add_flow_rules+0x30/0x490 [mlx5_core]
[ 826.452829] mlx5_add_flow_rules+0x30/0x490 [mlx5_core]
[ 826.453368] ? __kmalloc_node+0x5a/0x120
[ 826.453733] esw_add_restore_rule+0x20f/0x270 [mlx5_core]
[ 826.454288] ? mlx5_eswitch_add_send_to_vport_meta_rule+0x260/0x260 [mlx5_core]
[ 826.455011] ? mutex_unlock+0x80/0xd0
[ 826.455361] ? __mutex_unlock_slowpath.constprop.0+0x210/0x210
[ 826.455862] ? mapping_add+0x2cb/0x440 [mlx5_core]
[ 826.456425] mlx5e_tc_action_miss_mapping_get+0x139/0x180 [mlx5_core]
[ 826.457058] ? mlx5e_tc_update_skb_nic+0xb0/0xb0 [mlx5_core]
[ 826.457636] ? __kasan_kmalloc+0x77/0x90
[ 826.458000] ? __kmalloc+0x57/0x120
[ 826.458336] mlx5_tc_ct_flow_offload+0x325/0xe40 [mlx5_core]
[ 826.458916] ? ct_kernel_enter.constprop.0+0x48/0xa0
[ 826.459360] ? mlx5_tc_ct_parse_action+0xf0/0xf0 [mlx5_core]
[ 826.459933] ? mlx5e_mod_hdr_attach+0x491/0x520 [mlx5_core]
[ 826.460507] ? mlx5e_mod_hdr_get+0x12/0x20 [mlx5_core]
[ 826.461046] ? mlx5e_tc_attach_mod_hdr+0x154/0x170 [mlx5_core]
[ 826.461635] mlx5e_configure_flower+0x969/0x2110 [mlx5_core]
[ 826.462217] ? _raw_spin_lock_bh+0x85/0xe0
[ 826.462597] ? __mlx5e_add_fdb_flow+0x750/0x750 [mlx5_core]
[ 826.463163] ? kasan_save_stack+0x2e/0x40
[ 826.463534] ? down_read+0x115/0x1b0
[ 826.463878] ? down_write_killable+0x110/0x110
[ 826.464288] ? tc_setup_action.part.0+0x9f/0x3b0
[ 826.464701] ? mlx5e_is_uplink_rep+0x4c/0x90 [mlx5_core]
[ 826.465253] ? mlx5e_tc_reoffload_flows_work+0x130/0x130 [mlx5_core]
[ 826.465878] tc_setup_cb_add+0x112/0x250
[ 826.466247] fl_hw_replace_filter+0x230/0x310 [cls_flower]
[ 826.466724] ? fl_hw_destroy_filter+0x1a0/0x1a0 [cls_flower]
[ 826.467212] fl_change+0x14e1/0x2030 [cls_flower]
[ 826.467636] ? sock_def_readable+0x89/0x120
[ 826.468019] ? fl_tmplt_create+0x2d0/0x2d0 [cls_flower]
[ 826.468509] ? kasan_unpoison+0x23/0x50
[ 826.468873] ? get_random_u16+0x180/0x180
[ 826.469244] ? __radix_tree_lookup+0x2b/0x130
[ 826.469640] ? fl_get+0x7b/0x140 [cls_flower]
[ 826.470042] ? fl_mask_put+0x200/0x200 [cls_flower]
[ 826.470478] ? __mutex_unlock_slowpath.constprop.0+0x210/0x210
[ 826.470973] ? fl_tmplt_create+0x2d0/0x2d0 [cls_flower]
[ 826.471427] tc_new_tfilter+0x644/0x1050
[ 826.471795] ? tc_get_tfilter+0x860/0x860
[ 826.472170] ? __thaw_task+0x130/0x130
[ 826.472525] ? arch_stack_walk+0x98/0xf0
[ 826.472892] ? cap_capable+0x9f/0xd0
[ 826.473235] ? security_capable+0x47/0x60
[ 826.473608] rtnetlink_rcv_msg+0x1d5/0x550
[ 826.473985] ? rtnl_calcit.isra.0+0x1f0/0x1f0
[ 826.474383] ? __stack_depot_save+0x35/0x4c0
[ 826.474779] ? kasan_save_stack+0x2e/0x40
[ 826.475149] ? kasan_save_stack+0x1e/0x40
[ 826.475518] ? __kasan_record_aux_stack+0x9f/0xb0
[ 826.475939] ? task_work_add+0x77/0x1c0
[ 826.476305] netlink_rcv_skb+0xe0/0x210
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/efa: Fix wrong resources deallocation order
When trying to destroy QP or CQ, we first decrease the refcount and
potentially free memory regions allocated for the object and then
request the device to destroy the object. If the device fails, the
object isn't fully destroyed so the user/IB core can try to destroy the
object again which will lead to underflow when trying to decrease an
already zeroed refcount.
Deallocate resources in reverse order of allocating them to safely free
them. |