| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: bsg: Pass reply_len to bsg_setup_queue() to fit UFS ARPMB replies
bsg-lib allocates a 96-byte (SCSI_SENSE_BUFFERSIZE) reply buffer per
job, but struct ufs_rpmb_reply is 104 bytes: a 40-byte struct
ufs_bsg_reply followed by a 64-byte EHS. When an Advanced RPMB command
returns an EHS, ufshcd_advanced_rpmb_req_handler() copies it right after
the 40-byte header and writes 8 bytes past the end of the buffer.
Let each BSG transport pass its reply buffer size to bsg_setup_queue()
and have ufs_bsg request sizeof(struct ufs_rpmb_reply), so the full
reply reaches user space. Other transports keep SCSI_SENSE_BUFFERSIZE. |
| In the Linux kernel, the following vulnerability has been resolved:
ring-buffer: Fix the sub-buffer array base in rb_meta_subbuf_idx()
On a persistent ring buffer, rb_meta_subbuf_idx() can return an index one
sub-buffer too high. rb_setup_ids_meta_page() then fills subbuf_ids[]
shifted by one and leaves subbuf_ids[0] NULL, which __rb_map_vma()
dereferences when userspace maps trace_pipe_raw. rb_update_meta_reader()
writes two such indices into meta->buffers[], which rb_cpu_meta_valid()
would reject on the next boot, discarding the previous boot's trace.
A CPU's sub-buffer array starts after its meta header and the nr_subbufs
integers that follow, aligned up to a sub-buffer. rb_meta_subbuf_idx()
inverts that calculation but skips only the integers, not the header, so
its base is one sub-buffer low whenever the omitted header size crosses
the alignment boundary.
Invert the calculation with rb_subbufs_from_meta() rather than repeating
it. rb_range_buffer() maps an index back to an address through the same
helper, so the two directions can no longer disagree. |
| In the Linux kernel, the following vulnerability has been resolved:
ring-buffer: Do not show buffer_meta for CPUs without a buffer
The per_cpu/cpuN/buffer_meta files are created for every possible CPU,
but buffer->buffers[cpu] is only allocated once that CPU comes online.
Reading the file of a CPU that never came online dereferences a NULL
cpu_buffer in rbm_start().
Fail the open with -ENODEV when the CPU has no buffer, as the other
per CPU ring buffer interfaces do. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing/histograms: Reject non-stacktrace fields for synthetic stacktrace fields
In check_synth_field(), when a synthetic event field is a stacktrace
(field->is_stack) and the histogram field is not a "long[" stacktrace
array, validation falls through to the generic size and signedness
comparison.
Because parse_synth_field() sets a stacktrace field's type to
"__data_loc unsigned long[]", its size is sizeof(u64) and
synth_field_signed() marks it as signed. Consequently, any 8-byte
signed scalar histogram field passes the fallback check, and its scalar
value is subsequently dereferenced as a kernel stacktrace pointer in
get_field_size() and trace_stack().
Furthermore, checking strstr(hist_field->type, "long[") is insufficient
because tracepoint fields defined with __bitmask() or __rel_bitmask()
also have type "__data_loc unsigned long[]" or "__rel_loc unsigned
long[]", whilst create_hist_field() treats them as 4-byte scalar values
without HIST_FIELD_FL_STACKTRACE.
Propagate HIST_FIELD_FL_STACKTRACE to variable references and field
variables (whilst excluding variable aliases from per-element
stacktrace capture), and reject any mismatch between
HIST_FIELD_FL_STACKTRACE and field->is_stack in check_synth_field(). |
| In the Linux kernel, the following vulnerability has been resolved:
spi: imx: fix slab corruption from undersized DMA bounce buffers
Since commit faa8e404ad8e ("spi: imx: support dynamic burst length for
ECSPI DMA mode"), the driver allocates its private DMA TX/RX buffers
with kzalloc(dma_len), where dma_len is only rounded up to 4 bytes, but
maps, syncs and unmaps them with DMA_CACHE_ALIGNED_LEN(dma_len), i.e.
rounded up to the cache line size. As a result, the DMA API operates on
memory beyond the end of the allocation.
This was observed on a custom i.MX8MP platform with an mcp251xfd CAN
controller under heavy RPMSG load, as a series of refcount_t warnings
triggered from rpmsg_recv_done() in virtio_rpmsg_bus:
refcount_t: addition on 0; use-after-free.
refcount_t: underflow; use-after-free.
refcount_t: saturated; leaking memory.
Leading finally to an "Unable to handle kernel paging request" oops.
Reproducing this problem took between 30 minutes and roughly 30 hours
under the same workload.
Hardware watchpoints on the refcount of a struct rpmsg_endpoint showed
it was overwritten from 2 to 1 by __pi_memcpy_generic() in the
irq/155-spi2.0 thread. Additionally it was found that a "normal"
rpmsg_recv_done() took 11µs +/-2µs from its kref_get to kref_put. In
the error case the same sequence took about 215µs +/-10µs. Based on
this, an LLM was used to identify the size mismatch fixed here.
Allocate the buffers with DMA_CACHE_ALIGNED_LEN(dma_len) so they cover
the full mapped length, and use the same length for
dma_sync_single_for_cpu() to stay consistent with map and unmap.
With this patch applied, the same workload ran for more than 200 hours
without the problem reproducing. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: revalidate output stream after association connect wait
When message interleaving is enabled, the first send waits for association
establishment before building its data chunks. The wait drops the socket
lock, and handshake processing can reduce the output stream count to the
peer-advertised inbound stream count. sctp_stream_init() then frees the
extension of every removed stream.
The sender resumes with the stream that it checked before the wait. If the
peer removed that stream, sctp_outq_tail() later dereferences its NULL
extension. Fatal-oops policies then panic the host.
KASAN: null-ptr-deref in range [0x38-0x3f]
RIP: sctp_outq_tail+0x49e/0xaa0
Call Trace:
sctp_primitive_SEND
sctp_sendmsg_to_asoc
sctp_sendmsg
A range check alone is insufficient. Stream reconfiguration can grow the
output count again while the lock is released without recreating extensions
freed by the earlier shrink. The stream can then be in range while its
extension remains NULL. The send-buffer wait has the same issue.
Factor the range and extension checks into a helper and repeat both after
each send-path wait that drops the socket lock. Once the lock is
reacquired, the validation remains stable through data creation and
queueing.
If validation fails after the connect wait, the auto-created association is
already established. Return ESRCH so the existing caller path keeps it
under state-machine ownership instead of freeing it directly, which would
leave protocol, counter and socket state inconsistent. |
| In the Linux kernel, the following vulnerability has been resolved:
mshv_vtl: Check per-CPU register page before mmap
Register-page setup is optional for each CPU. If allocation or
registration fails, mshv_vtl_configure_reg_page() warns and leaves that
CPU's reg_page NULL, but initial context setup continues successfully.
Meanwhile, successful setup on another CPU sets the global
mshv_has_reg_page flag.
mshv_vtl_fault() checks this global flag before selecting the requested
CPU's register page. With mixed setup results across online CPUs, the
check passes even for a CPU with no register page, reaching
get_page(NULL) when userspace faults in that mapping.
Check the selected per-CPU register page before taking its reference and
return VM_FAULT_SIGBUS if it is absent. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: free the sbi after a grace period
ext4_get_link() follows a symlink that keeps its target in a data block
in rcu pathwalk mode with ext4_getblk(EXT4_GET_BLOCKS_CACHED_NOWAIT).
That reads s_mount_state in the ASSERT() of ext4_getblk() and again in
ext4_es_lookup_extent(), and the lookup bumps the extent status hit or
miss counter, all through sb->s_fs_info.
ext4_put_super() destroys those counters, clears sb->s_fs_info and frees
the sbi without waiting for a grace period. A pathwalk that is still in
ext4_get_link() when the last reference to the mount goes away then
dereferences a NULL s_fs_info, the freed sbi or the destroyed percpu
counters.
With a pathwalk held up in ext4_get_link() while the last reference
goes away:
KASAN: null-ptr-deref in range [0x00000000000000a8-0x00000000000000af]
RIP: 0010:ext4_getblk+0xf0/0x640
Call Trace:
<TASK>
ext4_get_link+0x26c/0x410
pick_link+0xf96/0x1780
step_into_slowpath+0x9b8/0x1250
path_lookupat+0x484/0xb00
filename_lookup+0x1f1/0x5b0
vfs_statx+0xd7/0x3b0
vfs_fstatat+0x4d/0x90
__do_sys_newfstatat+0xa0/0x100
do_syscall_64+0x10e/0x5e0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
So far that has been hard to hit. umount(2) waits for a grace period in
namespace_unlock() before it drops the mount, so only a mount whose last
reference goes away elsewhere, like the close of a file or a chdir out of
a lazily unmounted directory, can race a walker.
Keep sb->s_fs_info and free the sbi together with the extent status
counters after a grace period. Split the counters out of
ext4_es_unregister_shrinker() for that. The shrinker still gets wasted
in ext4_put_super(), the counters go with the sbi. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: nVMX: Reset MMU back to the root MMU if loading L2 state fails for !VM-Entry
Reset the vCPU's MMU pointer back to the root MMU if loading L2 state fails
in the "not from VM-Entry" case, i.e. when emulating RSM or handling
KVM_SET_NESTED_STATE. Failure to unwind the MMU pointer results in KVM
trying to run L1 with a nested MMU, and is especially problematic if the
vCPU manages to free its nested state before the VM crashes. Constructing
the root for a nested EPT MMU goes through vmcs12, which is dynamically
allocated/freed when nVMX is enabled/disabled. And so if the nested state
is freed with the MMU still pointing at the nested MMU, KVM will hit a NULL
pointer deref when attempting to get L1=>L2 EPTP.
BUG: kernel NULL pointer dereference, address: 0000000000000078
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 114a2d067 P4D 111743067 PUD 11141f067 PMD 0
Oops: Oops: 0000 [#1] SMP
CPU: 20 UID: 1000 PID: 1272 Comm: nested_tdp_faul Not tainted 7.3.0-rc4-8c89f11d1a99b-sink-vm #1914 PREEMPTLAZY
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:nested_ept_get_eptp+0xb/0x10 [kvm_intel]
Call Trace:
<TASK>
kvm_mmu_load+0xcd/0x870 [kvm]
kvm_arch_vcpu_ioctl_run+0x18f5/0x1f80 [kvm]
kvm_vcpu_ioctl+0x2c7/0x970 [kvm]
__x64_sys_ioctl+0x90/0xd0
do_syscall_64+0x9c/0x4d0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x47491b
</TASK>
Modules linked in: kvm_intel kvm irqbypass
CR2: 0000000000000078
---[ end trace 0000000000000000 ]---
RIP: 0010:nested_ept_get_eptp+0xb/0x10 [kvm_intel]
[sean: write changelog] |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fill in FileSysIdentifier in FS_POSIX_INFORMATION
smb2_get_info_filesystem() reports 56 bytes for FS_POSIX_INFORMATION,
that is the whole of FILE_SYSTEM_POSIX_INFO, but never assigns
FileSysIdentifier. Those eight bytes go to the client as they are found
in the response buffer.
The buffer is zeroed on allocation, so a standalone request leaks
nothing. A compound request can leak: the offset of the next response
is advanced by the length pinned for the previous one, so a reply that
was written into the buffer and then dropped in favour of the short
error response of smb2_set_err_rsp() stays there, and the next reply is
laid over it with only the header cleared.
Report the file system id statfs() returned, which is what the field is
for. FileSysIdentifier is __le64 and f_fsid is a pair of ints, so
assemble the value first, val[0] as the low half, and convert it on the
way out. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/userq: actually validate userq BOs
This was supposed to loop over the individual evicted list, as the
kernel and always_valid evicted lists were already handled in
amdgpu_vm_validate.
Without this, BOs that were created and evicted before a userq was made
would never end up in an eviction fence rearm.
Also add the missing ref to the BO before drm_exec locks and refs it.
(cherry picked from commit 18decfc9e8cc0fa70b6de9944cc27a37729edfbd) |
| In the Linux kernel, the following vulnerability has been resolved:
s390/pci: Fix leak of uninitialized kernel data in SCLP report
While report_error_write() checks that the provided buffer is at least
as large as the header struct, but not that it is large enough to
contain the report with the length claimed by report->length. If
user-space provides a short buffer, meaning a larger report->length than
the actually written payload, up to around 4K of kernel data from past
the kmalloc(len + 1) sized buffer allocated in kernfs_fop_write_iter()
will leak into the SCLP report.
However, as the entity processing the SCLP is privileged and able to
access at least the page including the report, this does not leak data
that entity could not access but it is still an out of bounds read and
a malformed error report that should be rejected. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix hist trigger timestamps for buffered events
Syzkaller triggered a WARN_ON_ONCE(!nest) warning:
WARNING: kernel/trace/ring_buffer.c:821 at ring_buffer_event_time_stamp
Call trace:
ring_buffer_event_time_stamp
hist_field_timestamp
hist_fn_call
event_hist_trigger
event_triggers_call
__event_trigger_test_discard
trace_event_buffer_commit
do_trace_event_raw_event_sched_switch
trace_event_raw_event_sched_switch
The warning is probabilistically reproducible and is related to syzkaller
executing the following commands:
echo 'prev_pid == 999999' > events/sched/sched_switch/filter
echo 'hist:keys=common_timestamp' > events/sched/sched_switch/trigger
The specific triggering process is as follows:
CPU 0 CPU 1
(context switching) (echo 'hist:keys=common_timestamp' > \
events/sched/sched_switch/trigger)
do_trace_event_raw_event_##call
trace_event_buffer_lock_reserve
if (!tr->no_filter_buffering_ref &&
trace_file->flags & EVENT_FILE_FL_FILTERED)
return entry; // return directly
event_hist_trigger_parse
hist_register_trigger
tracing_set_filter_buffering(file->tr, true);
tr->no_filter_buffering_ref++;
__trace_buffer_lock_reserve
rb_start_commit
local_inc(&cpu_buffer->committing); // skipped and not executed
trace_event_buffer_commit
__event_trigger_test_discard
event_triggers_call
event_hist_trigger
hist_fn_call
hist_field_timestamp
ring_buffer_event_time_stamp
nest = local_read(&cpu_buffer->committing);
WARN_ON_ONCE(!nest) // trigger warning
The root cause is that when an event file has a filter attached and the
hist trigger has not yet been attached, trace_event_buffer_lock_reserve()
writes the event into the per-CPU trace_buffered_event temp buffer instead
of reserving it in the ring buffer, so cpu_buffer->committing is not
incremented. When the event is later processed at commit time by a hist
trigger, hist_field_timestamp() -> ring_buffer_event_time_stamp() sees a
zero committing count, triggering WARN_ON_ONCE(!nest).
tracing_event_time_stamp() was added by commit d8279bfc5e959 ("tracing:
Add tracing_event_time_stamp() API") for exactly this case: if the event
is the per-CPU trace_buffered_event, it returns the current ring buffer
timestamp. But it never gained a caller. Use it in hist_field_timestamp(),
so that a hist trigger that races onto a buffered event records the
current time, which is only marginally later than when the event was
recorded, instead of warning and recording a bogus timestamp. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix crash in print_graph_function_event()
tracing_set_tracer() assigns the flags of the newly selected tracer
with:
tr->current_trace_flags = t->flags ? : t->tracer->flags;
If the new tracer defines neither static flags nor default flags, like
hwlat, irqsoff or wakeup, add_tracer() has no per instance flags copy
for it, and both operands are NULL, so tr->current_trace_flags ends up
being NULL as well.
The ring buffer is not cleared when switching tracers: it is reset
inside tracer_init(), after current_trace_flags was already assigned.
If the buffer still holds function_graph entries of the previous
tracer, printing one of them dereferences the NULL pointer. This was
hit by cat trace during an ftrace stress test:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
RIP: 0010:print_graph_function_event+0xe/0x20
Call Trace:
s_show+0x4d/0x110
seq_read_iter+0x2d4/0x490
seq_read+0x130/0x170
vfs_read+0xb5/0x370
ksys_read+0x6d/0xe0
do_syscall_64+0xbc/0x450
The snapshot buffer is not reset at all, so this can be reproduced
without a race:
echo function_graph > /sys/kernel/tracing/current_tracer
echo 1 > /sys/kernel/tracing/snapshot
echo hwlat > /sys/kernel/tracing/current_tracer
cat /sys/kernel/tracing/snapshot
Rather than teaching every user of tr->current_trace_flags about this
corner case, make sure it is never NULL: when the newly selected
tracer has no flags at all, tracing_set_tracer() falls back to a
static empty no_tracer_flags. run_tracer_selftest() can hit the same
case, so the same fallback is added there too. The existing users
already handle opts == NULL, so these tracers keep behaving as before. |
| In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Fix use-after-free of a destroyed user DSQ by a deferred reenqueue
A deferred reenqueue can read a freed user DSQ. The request stays on its
CPU's deferred list until run_deferred() takes it, and the RCU callback that
frees the DSQ assumes that the grace period has flushed it, so exit_dsq()
checks the per-CPU node without the deferred list lock. A grace period waits
for readers in flight, not for a pending run_deferred(). A run_deferred()
which starts after the grace period began can detach the request right
before the callback looks and then read the freed DSQ's id.
Cancel the pending requests before the grace period instead. The irq work
that frees the DSQ unlinks every CPU's request under the per-CPU deferred
list lock, and schedule_dsq_reenq() ignores a new request under the same
lock once the id is invalid. Only a run_deferred() that started before the
grace period can hold a request, and it runs with IRQs disabled, so the
grace period waits for it and nothing touches the DSQ after the callback. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe: Don't transfer shrinker pages for pinned bos on purgeable state change
Pinned bos have their pages removed from the shrinker's shrinkable /
purgeable counts on pin, and added back on unpin according to the
bo's purgeable state at that time.
However, xe_bo_set_purgeable_shrinker() unconditionally transfers
pages between the shrinkable and purgeable counts. If the purgeable
state of a pinned bo changes, for example by userspace madvising
DONTNEED on a VMA of a bo that is also pinned as a scanout buffer,
this underflows one count and, after unpin, leaves the other one
permanently inflated.
Only update the purgeable flag for pinned bos, and leave the page
accounting to unpin.
(cherry picked from commit afe6bc012034123fd838328668e609bf57e46bd3) |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: avoid divide by zero in fib_rebalance
fib_rebalance() computes the total eligible nexthop weight in one pass
and programs upper bounds in a second pass. A concurrent change to
ignore_routes_with_linkdown can make the first pass return zero while
the second pass sees an eligible nexthop, resulting in division by zero.
If the first pass reports a zero total, set each nexthop upper bound to
-1 and skip the division. This matches the IPv6 fix in commit
d2c26c2911dd ("ipv6: avoid divide by zero in rt6_multipath_rebalance")
and preserves the lock-free rebalance path. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915/dmc: Add sanity check for DMC load address
For DMC firmware header version 3, the firmware load address is stored
in dmc_info->start_mmioaddr and later used by dmc_load_program().
Unlike the MMIO address table, the firmware load address is not
validated. Add a sanity check to ensure it is within the valid range.
BSpec: 69671, 68378
(cherry picked from commit 5e47ee5c76ca9becde8df4ad5202845b7ffcbc4c) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/exec: don't immediately add prelocked obj to array of locked objs
When a contention is detected the drm_exec object grabs a reference to
the contended object, unlocks all other objects and pre-locks the
contended one before anything else.
The problem is that it is possible that this pre-locked object was about
to be destroyed and drm_exec is now holding the last reference to it.
So we never actually see this pre-locked object again to be explicitly
locked and so also never reserve a slot for a dma_fence object on it.
Should the driver now use drm_exec_for_each_locked_object() to add a new
fence to all locked objects we eventually see a warning or even a
BUG_ON() to prevent random memory corruption.
Fix this by keeping the prelocked object out of the array of locked objs
until it was explicitly mentioned by the driver again.
If the prelocked object is never mentioned again by the driver
just unlock and drop the reference at the end of the locking loop. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix GEM object leak on ENOMEM in userptr ioctl
When amdgpu_hmm_range_alloc() fails amdgpu_gem_userptr_ioctl() returns
-ENOMEM right away and skips the cleanup every other error path goes
through. The GEM object, the bo->parent reference on the VM root and the
MMU notifier registration are all left behind.
Use release_object here, not user_pages_done, range is still NULL at
this point.
(cherry picked from commit bbe739e407a542073ec1a7872b14843566b4919e) |
